The cheapest LCD I have found online is through The Foto Geeks for $55, however you can actually buy a cheaper whole (working) camera from eBay, and usually accessories are included with it. Note to make sure it is only the LCD which is cracked and not the backlight, in order to get the correct replacement parts.

My poor camera with cracked LCD screen:

Tools required:

• small Philips head screwdriver
• small flat head screwdriver

First remove the 6 Philips screws on the edges of the metal case, location defined by the arrows in the photo below:

Remove the front half of the metal case by starting at the camera’s base, at the top there is a metal clip which connects the front and back halves. Removing the front half free form this clip requires a bit of manipulating . The clip is circled in the photo below:

Once the front half of the metal housing is removed, the back half can be removed extremely easily. You will be presented with the LCD screen, remove the single Philips screw which holds the LCD in place as per the photo below:

Slide the LCD screen to the left, and this will release the screen from a little clip. Once the screen is free, remove a Philips screen holding the tripod mount is place:

Turn the camera over, and remove the front screw which holds the tripod mount. You can then remove the tripod mount which will allow the removal of the main LCD ribbon cable. The ribbon cable is disconnected by lifting up the brown tab on the connector:

Once the main ribbon cable is removed, the backlight’s ribbon cable can then be accessed easier. It is removed by simply pulling the cable away from the socket perpendicular to the PCB:

The LCD can now be removed from the camera. The below photo is the replacement LCD screen:

To connect the replacement LCD and reassemble the camera, perform the above instructions in reverse. It is a good idea to test the replacement LCD before assembling, to make sure everything works fine.

I finished sanding the bezel to a state I was quite happy with. The hole was then trimmed as it was slightly too big and the sides were uneven.

Pictures below just before painting.

First a white undercoat, 2 layers.

Coat of matt black, 2 layers.

Final photos of the Videosphere shell with new bezel.

The LCD screen, after having the corners trimmed.

The LCD screen was glued in place, will be cleaned of glue smudges as the end.

Next, I am looking at connecting the LCD circuitry.

Here is the last update for the year, going on holidays and won’t be back till mid January.

I have started to try to mount the LCD TV into the Videosphere. Firstly removed the LCD from the plastic housing

This is a photo of the back of the LCD

First fit test. You would not believe how close this panel is to not fitting. When choosing the TV I only was concerned about the LCD size fitting the hole, I did not think about the housing. Being a cheap quality LCD the housing protrudes a fair bit. You can observe that the housing isn’t quite flush and this is for two reasons, the LCD is slightly too big, and the hole is actually curved due to the curved screen of the original CRT.

The way I solved the LCD size problem was grinding the corners down. This was fairly dangerous as it was easy to damage the LCD, I still haven’t tested the LCD to see if it still works. Before grinding I disassembled the metal housing, this was so that I could see where the glass was as you do not want to be grinding that.

Here is a photo of the ground corners of the metal housing; I will explain what the cardboard is for next.

This now solved the LCD not fitting problem. The next problem was the gaps caused by the curved hole. This was solved by using car body filler. First I made a cardboard template with the exact same size hole as the Videosphere.
You can observe the LCD metal housing on top of the cardboard below.

It was secured to the Videosphere with some tape.

Car body filler was applied liberally over the cardboard.

And the sanding process began.

I decided to buy myself an early Christmas present to speed things up. $125 from Bunnings, includes the Flex Shaft and 55 accessories.

This was the finished results after another layer of car body filler. It took me a while to get used to the Dremel as I was taking too much out of some areas and leaving indents.

I am quite happy with the results so far. This will be painted black making any imperfections harder to see. Below is a photo of the LCD metal housing over the hole. The hole is slightly uneven and small and that will be fixed up next year.

I picked up the Videosphere about 3 years ago of eBay for about $200.

I will also mention, I am going to try and include everything, even the mundane stuff. So with that said.
Here are some pictures of me washing it. Basically I removed everything that could be removed and scrubbed it with a bit of detergent and brush. The condition is actually quite good, few scratches but nothing major.

This is the colour LCD TV I purchased of eBay about a year ago for $150. I spent a while looking for one that could fit the nicest in the existing hole. The actual tube is specified as 9″.

I also picked up a few sheets of various grade wet and dry for $1.30 each.